This publish about how to make 3 Uncomplicated Do it yourself Floating Image Frames And How to Lower Plexiglass is sponsored by The Home Depot as portion of the #THDProSpective Application. It also has affiliate one-way links. See policies.
Easy Do it yourself photograph frames are essentially a person of my most requested tutorials and oddly more than enough, until eventually now, I didn&rsquot have several to share!
.
I actually developed my dad a enormous Diy custom made picture frame as a Christmas present a few many years back and shared the tutorial for it listed here. But it used dowels, and a router, and it may have been a tiny a lot more included than most people today are looking for.
So, in this post, I&rsquom heading to show you how I created three unique design and style Super Simple Diy floating photo frames with just two basic equipment. I&rsquoll also display you how effortless it is to reduce plexiglass for them, far too!
.
So if you&rsquore prepared to get creating, let&rsquos go! I&rsquove obtained the video clip tutorial below and the action by move down below:
Applications AND Resources:
- Miter noticed (or any wood reducing observed is fantastic&ndashdoesn&rsquot have to be a MITER observed)
- Nail Gun (optional, just will make matters more rapidly)
- Wood Glue
- ¾&Primary square dowels
- one×2 boards
- ¼&Prime x 1 ⅛&Primary lattice trim
- Skinny Plexiglass Sheets
- Ryobi One+ HP Slash Off Instrument (made use of to lower plexiglass)
- Clamps (also optional&ndashif you don&rsquot have clamps, you can use CA glue or painters tape in position of clamps to maintain items even though wood glue dries)
- Flip buttons
A Be aware About FLOATING Image Frames:
I&rsquom sharing how to make 3 unique model FLOATING image frames in this tutorial, but the to start with stage to building any of them is chopping the plexiglass to the dimension you want.
.
If you don&rsquot want to use plexiglass for your frames, you can skip this phase. But since the graphics/photos I framed are &ldquofloating&rdquo within the body, they&rsquore fundamentally sandwiched between two items of plexiglass. So plexiglass/acrylic is needed to be in a position to &ldquofloat&rdquo your picture.
.
To make things effortless to modify out in these frames, I also employed these switch buttons&mdashor I contact them twisty tabs&ndashon the back again to maintain the plexiglass in spot.  
HOW TO Lower PLEXIGLASS
Commonly, I have my nearby glass shop cut my glass and plexiglass pieces for my jobs.  But because these plexiglass parts will be small and different personalized dimensions, it would be a lot much less expensive, more quickly and simpler to just lower them myself.
.
I utilized some (about) ⅛&rdquo acrylic sheets from Property Depot.  They occur in several sizes, all the way up to a 4×8 sheet.  I just grabbed some 11x14s.
I created some uncomplicated graphics on my laptop (PicMonkey and Canva are great for this!) and also utilised a patch that I won a number of yrs back at a conference for these frames.  You can use a picture, a poster, cloth, no matter what you want to frame for this.
.
I laid them out on my sheet how I appreciated the spacing, then marked the place I required to slash&ndashno measurements right here&hellipjust eyeballing how I assumed the spacing all around the impression appeared fantastic.
Now, I&rsquove employed the cheap small hand knife they assert will slice plexiglass ahead of and it was a horrible encounter with extremely very poor benefits.  I&rsquove also made use of a jig noticed to minimize plexiglass and it melts, receives caught, then chips or cracks the sheet.
.
So THIS time, I tried this new Ryobi One particular+ HP Compact Slice Off Resource with a plastic cutting blade and was thoroughly amazed with how fast and clear the cuts were.
When I to start with noticed this tool, I found it variety of strange hunting.  But just after I used it, I recognized the strategy. 
.
It&rsquos fundamentally a hybrid in between a drill and an angle grinder. It cuts like an angle grinder, but it feels a drill with the head turned ninety levels. 
.
It&rsquos compact and lightweight and it&rsquos received a forward and reverse change to transform the blade equally instructions.  It&rsquos also bought a variable speed cause&mdashwhich is very good for cutting plastic to support stop melting. 
It arrives with a plastic and drywall blade, a metal reduce off wheel, and a diamond blade for slicing tile and cement board.  You can find out more about the new Ryboi One+ HP slash off resource at the url listed here if you&rsquore fascinated.
.
For slicing straight lines on the plexiglass, I just lined up a straight edge (scrap piece of wooden), clamped and ran the metallic blade guard versus it to make the slash.  You can skip the straight edge and freehand these cuts, much too if you have a regular hand. (I don&rsquot haha!)
I did come across it lower best in this scenario with the change in reverse. It appeared to not soften that way.
.
I slice two pieces similar in size for every single item I was framing. Then, I was ready to commence creating the true floating picture frames.
Easy Do it yourself FLOATING Photograph Body Model one
Style one is my individual beloved, so I&rsquoll get started with it 😊
This specific floating image frame layout requires ¾&Key square dowels and one×2 board. It is mainly just a 1×2 wrapped all-around a square dowel frame.
.
I employed ¾&rdquo sq. dowels for this and established up my miter observed to lower forty five levels.  Now, you don&rsquot have to miter these.  You can leave it on 90 and make butt joints.  You also don&rsquot require a MITER observed for this.  Any saw that you can minimize pretty straight with will do the job wonderful.
.
I mainly trimmed 4 parts of sq. dowel so that when healthy collectively, they&rsquod be just barely (like ⅛&Key) even bigger than the plexiglass piece I was placing in it.
I used wooden glue to the corners and nailed them collectively with brad nails.  If you are individual, and don&rsquot have a nail gun, just glue and clamp until finally dry.
.
Right after the glue had dried, I slice to fit 1×2 items with 45 diploma mitered corners all-around this frame.  Once again, butt joints are great here if you want to skip the mitered corners.
.
I glued and nailed these 1x2s all-around the edges leaving about ¼&rdquo sticking out the back side of the plexiglass, so that when I put in the two ⅛&Prime plexiglass parts, it&rsquoll be flush throughout the again facet of the frame.
Then, I screwed these twisty tabs into the back sides of the body to hold the plexiglass in put.  I&rsquoll go back again and clear the sawdust off the plexiglass afterwards, but for now, I set this off to the facet to make the following frame.
Effortless Do it yourself FLOATING Photo FRAMES Design and style 2
Design 2 is a minimal simpler and is created of 1x2s and ¼&rdquo thick by one ⅛&Primary vast lattice trim.
I commenced by cutting down the lattice items so it would make a body that the plexiglass would in shape Inside.  Once again, just like right before, the mitered corners are optional.
As soon as I experienced this lattice frame minimize, I calculated its in general dimension and reduce one×2 items to make a frame whose all round dimension matched that of the lattice body. See under one×2 frame laying on best of lattice body&ndashthey&rsquore the exact same dimension.
I glued and nailed the 1×2 body collectively and clamped until eventually dry. Once again, you can use tremendous glue or painters tape if you don&rsquot have a nail gun or clamps 🙂
.
Then, I flipped it upside down and glued the lattice frame onto the back.  I utilized a large object to keep it in location right until it was dry, then, I screwed twisty tabs on the back again to keep the plexiglass in area. 
Since the lattice is ¼&rdquo thick, and the plexiglass is ⅛&rdquo thick, when the two plexiglass pieces are placed inside of, anything need to sit flush throughout the again just like the final frame.
Again, I&rsquoll go again and clean the sawdust off later on, but for now, I moved on to the very last design and style frame.
Quick Do it yourself FLOATING Photograph Frame Model 3
Type 3 is the very same strategy as type one, but rather of working with 1x2s, I used ¼&Primary x one ⅛&Primary lattice trim to preserve the frame a tiny thinner and a lot more minimalist wanting.
So, I cut ¾&rdquo square dowels to make a frame the identical dimension or a little greater than the plexiglass I was framing and glued and nailed it jointly.
Then, I minimize lattice trim to wrap close to that body. 
I glued the lattice trim on so that there was about ¼&rdquo sticking off the back side of the sq. dowel body so that when the two pieces of ⅛&rdquo plexiglass are put in, it&rsquoll all be flush across the again.
.
I didn&rsquot have any brad nails short plenty of to nail this body on, so I simply glued and clamped until eventually it was dry.
If you don&rsquot have clamps, you can use painters tape to variety of wrap all around the items to keep till the glue dries OR basically use some super glue or CA glue to assistance maintain parts in location till the genuine wooden glue is remedied.
.
Then, just like the very last two frames, I put in twisty tabs to maintain the plexiglass in spot.
FLOATING Photograph Frame HANGING Alternatives
The remaining action is cleanse up and hanging.  directory made use of some glass cleaner to cleanse up all the saw dust, then applied a piece of double sided tape on the again plexiglass piece to make sure the pics remain in location, then put the frames back with each other.
.
To hang, you can use your standard sawtooth hangers for this.
Or basically position it on a shelf.
.
OR, use a drill to drill holes into the corners to run some paracord and cling it on a piece of wooden dowel you screwed into the wall.
As you can see, making image frames doesn&rsquot have to be challenging.  This is a fantastic starter challenge you can deal with with minimal tools and get as resourceful as you want. 
.
I really hung these graphics up in my desk spot to aid keep me inspired when functioning by itself from residence right now. So, now that my desk area is comprehensive, I guess I really should almost certainly get back again to get the job done 😊
I hope you&rsquove liked this minor job.  There are a good deal additional coming your way, so be sure to subscribe to my publication underneath so you don&rsquot miss out on what&rsquos coming up coming!
.
And don&rsquot forget to pin this for later!
Till up coming time, satisfied developing 😊
 
